Tilcon New York New Jersey
NY
1-800-TRAPROC
NJ
1-800-789ROCK
Email Tilcon
 
Locations
New Jersey
New York
By Product
View a Map
Home Locations New York Clinton Point
 

Print PagePrint

Clinton Point, New York

Clinton Point Quarry
Sheafe Road
New Hamburg, NY 12590

Clinton Point Stone Quarry
PRODUCTS Stone, Asphalt
   
PHONE  
  Pricing: 845-480-3249 or 845-480-3190
  Orders: 800-872-7762
     
HOURS*

Stone:
Monday to Friday 5:30am to 4pm.
Saturday 6am to 2pm

Asphalt:
Monday to Friday 7:00am to 3:30pm.

* Facility may open outside of these hours based on customer demand.  Please call our NY Order Department or your Sales Representative for details.
   
DIRECTIONS
Take the NYS Thruway to Exit 17 (Newburgh). After the toll, bear right and then make first right which merges into Union Ave. Go approximately 1/4 mile to exit for Route 84 East. Take Route 84 East across Hamilton Fish Bridge (Newburgh/Beacon Bridge) to Exit 13, Route 9 North. Stay on Route 9 North to first left after Poughkeepsie Galleria Mall on Old Post Road. Down the hill to the stop sign and make a left onto Sheafe Road. The entrance to the asphalt plant is first and the quarry next entrance to right.

PRODUCTS:

Rock Type: Dolomite
Specific Gravity: Bulk (SSD) 2.81, range 2.793 – 2.828 *
Source No: 8-9R
* Specific gravities and unit weights are subject to change and should be verified before use

STONE

Application

2 1/2"

Used as railroad ballast, as a septic system bedding material and for tracking pads

1 1/2 ”

Used in tracking pads and erosion control

1 1/4"

Used in hot mix aphalt and drainage

3/4"

Used in hot mix asphalt, Portland cement concrete and as a drainage material

ASTM 57 Used in concrete and drainage
1/2" Used in hot mix asphalt and concrete
3/8”

Used in hot mix asphalt and Portland cement concrete

1/4" Used in hot mix asphalt and block mix

Manufactured Sand

Used in hot mix asphalt, Portland cement concrete, septic system bedding material
Screenings Used in hot mix asphalt, in many types of aggregate blends for specialty products
Item 4 Used as a sub base under roadways, compactable fill material
Rip Rap
2” – 6”
Used in erosion control, pipe outlets, walls for ground stabilization, jetty projects
Rip Rap
6” – 12”
Used in erosion control, pipe outlets, walls for ground stabilization, jetty projects
Rip Rap
12” – 24”
Used in erosion control, pipe outlets, walls for ground stabilization, jetty projects
Rip Rap
2-5 ton
Used in erosion control, pipe outlets, walls for ground stabilization, jetty projects
Rip Rap 5-10 ton Used in erosion control, pipe outlets, walls for ground stabilization, jetty projects
Fine Stone Fill Used in erosion control
Lite Stone Fill Used in erosion control
Medium Stone Fill Used in erosion control
Heavy Stone Fill Used in erosion control
**Not always readily available, please speak to your Sales Rep or Inside Sales for availability.

ASPHALT

Application

Marshall Mixes:  

Type 1 Base

A dense graded base or binder course

Type 3 Dense Binder

A dense graded base or binder course

Type 6 Top (Regular Fine)

A surface course for medium to heavy traffic roadways

Type 7 Top (Extra Fine)

A fine surface course
Curb Mix A fine mix used for curbs
Superpave:  
37.5mm A course graded base course used for all traffic levels with different ESAL levels
25mm A course graded binder course used for all traffic levels
19mm A dense graded binder course used for all traffic levels
12.5mm A surface course used for all traffic levels with different ESAL levels
Shim Used as a fill material to repair small areas in roadways and parking lots
Please note: All NY asphalt plants supply NY State DOT approved mixes.

View an Aerial Map

You will need Adobe Acrobat to properly view the form.
Click here to get Acrobat


  162 Old Mill Road, West Nyack, New York, 10994  Tel. 1 (845) 358-4500
© Copyright Tilcon New York Inc. All Rights Reserved. Privacy Policy | Terms of Use | Site Map
Visit the Web Designers - Northern Pride llc of Sparta New Jersey